







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tremron Kitchen Remodeling: The Coral Gables Owner’s Guide
If you’re pricing a Tremron kitchen remodel in Coral Gables, most projects land between $14,000 and $45,000 installed, depending on cabinet layout, surface square footage, and whether the electrical or plumbing rough-in has to move. We don’t sell parts off a shelf or run a parts counter. We’re an independent remodeling contractor that installs Tremron-compatible kitchen materials, we’re not affiliated with Tremron, and we give you a written price before any work starts.
How owners usually find us: a fixed cabinet front starts peeling at the bottom edge after two wet seasons, a surface panel chips near the sink where the substrate was never sealed, or a door hinge plate pulls loose from a cabinet box that wasn’t rated for the door weight. In Coral Gables, that’s the pattern. Salt air, humidity that sits near 80% most of the year, and the fine spray that drifts west from Biscayne Bay all push the same failure points faster than the inland spec sheets assume. We see it most often in homes built between the 1950s and the 1980s where the kitchen still has its original framing under a newer surface.
Which Tremron Models This Applies To

Tremron builds in several distinct material lines, and the compatibility question isn’t a logo question, it’s a dimension and series question. Kitchen projects typically involve their surface and panel lines (countertop slabs, backsplash tile, and cabinet-facing panels), not their hardscape lines (pavers, wall blocks, and coping). Those are a different spec family entirely, and a paver specification won’t cross over to a kitchen application even on the same finish name.
To identify what you actually have, pull the spec plate or the stamp on the back of the panel or the underside of the slab. Look for:
- A series or collection name, not just “Tremron”
- Nominal thickness (kitchen surfaces typically run 2cm or 3cm for slabs; panels vary by line)
- Finish name, because the same color reads differently across series
- A batch or lot number, which is what actually determines whether a replacement piece will match the one your neighbor bought two years later
If the stamp is worn or missing, measure the piece. Length, width, and thickness on a caliper will tell a trained eye which series you’re in. On the OEM-versus-aftermarket call: OEM is the right answer when you need a visible match (a peninsula end panel next to a ten-year-old slab). A quality aftermarket equivalent is the right answer on hidden components (substrate, backing, sealant, hardware). Our technicians have up to 22 years of experience across both paths, and we work from the manufacturer’s documentation on every specification, the same way we handle KraftMaid, Cambria, and Silestone projects. If a match can’t be confirmed from the stamp and the measurement, we say so before you spend the money.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Tremron Kitchen Remodeling Is Failing
The failure isn’t dramatic. It’s gradual. Here are the five we see most in Coral Gables kitchens:
- Edge lifting on the countertop. That’s usually a substrate problem, not a surface problem. The plywood or cement board underneath absorbed moisture and swelled, and the surface is doing its best to stay flat over a base that isn’t.
- Discoloration or a cloudy film across the surface. Under Florida sun through a south or west window, UV exposure plus humidity pushes a finish toward haze faster than the manufacturer’s lifespan estimate allows. A dull patch that won’t polish out is usually finish degradation, not dirt.
- Caulk lines re-opening within a season. Movement at the joint or a sealant that wasn’t rated for a wet, humid environment. Coral Gables kitchens near the water see this constantly. The joint flexes and the sealant gives before it should.
- Chipping at the sink cut-out or the cooktop edge. Frequently a fabrication issue, where the cut was made before the substrate was properly supported. The chip starts at the weakest point and runs.
- A hollow sound when you tap the surface. A hollow sound means the adhesive bond has separated. Once it’s separated, water gets under the panel and the failure accelerates quickly.
Any one of these is worth an inspection. Two or more together, and you’re likely facing a partial rebuild of the substrate, not just a surface swap. That’s a different scope and a different number, and we price both before you decide.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s the honest range for Coral Gables, broken out by the work that’s actually involved:
- Full kitchen remodel: $14,000 – $45,000
- Small kitchen remodel: $9,000 – $20,000
- Cabinet installation: $4,000 – $13,000
- Countertop installation: $2,000 – $6,500
- Backsplash installation: $800 – $2,500
- Kitchen island installation: $3,000 – $10,000
What moves you up or down that range: whether the substrate has to be replaced, whether the electrical rough-in needs to move for a new layout, and the finish selection. The installation line is labor and setting materials. The surface or cabinetry line is the material itself. We put both on one written sheet so you can see exactly where the money goes, and that price doesn’t move at the door.
Every completed project is covered by our 365-Day Done Right Promise. If the work fails within that year, we come back and correct it at no charge. That guarantee is written and signed, in your hand, at close. Site clean at close, documented scope, and the promise in writing: that’s what squared away looks like on a Bradford job.
DIY or Call Us?
You can safely check a few things yourself. Look for soft spots around the sink and the cooktop cut-out by pressing gently. Run a level across the countertop to see if it’s still true. Tap the surface to listen for delamination. Photograph the spec stamp before you call, because that speeds up the match. None of that is dangerous.
What’s not a weekend job: pulling a fixed panel or surface section off a substrate that may be hiding water damage, cutting new fabrication on a surface that isn’t rated for a homeowner cut, or resetting a cabinet box that’s out of plumb. Get the fabrication wrong and you’ve voided the manufacturer’s warranty on the material and created a worse problem than the one you started with. On any remodel involving the electrical or plumbing rough-in, that’s licensed trade work, full stop, and it’s not a DIY category.
If you want to know what your actual scope looks like, call us at (833) 510-5367. A live person answers, day or night, and the estimate is free.
FAQs

Ten to fifteen years is the realistic range in Coral Gables conditions, shorter than inland spec sheets suggest because salt air and year-round humidity accelerate sealant failure and finish wear. A surface installed over a properly sealed substrate and resealed every few years will run toward the long end. Call (833) 510-5367 for an exact quote on your scope. Estimates are free.
Sometimes. A single localized chip or a re-opened caulk joint can often be repaired if the substrate underneath is still sound. Delamination, edge lifting, or a hollow tap usually means the bond has failed, and a patch over a failed substrate won’t hold. We inspect first and tell you which one you’re looking at before we price it. Call (833) 510-5367 to schedule the inspection.
A countertop and backsplash swap usually runs three to five working days once materials arrive, while a full kitchen remodel with cabinetry runs two to four weeks depending on layout changes. Lead time on the material itself is the bigger variable, and we tell you the delivery window in writing before work starts. Call (833) 510-5367 for a written timeline and price.
We source from the manufacturer’s documented line and match by the series name and lot or batch number on your existing piece, not by color name alone. The lot number is the thing most homeowners miss, and it’s what determines whether a replacement piece reads as a match or as a near-miss. If a true match can’t be confirmed, we say so before you order. Call (833) 510-5367 to start the match.
Bradford Remodeling Co Coral Gables works with a documented roster of name-brand materials, including Tremron-compatible lines alongside KraftMaid, Cambria, and Silestone. Every project gets a written price before any work starts, and every completed job carries the 365-Day Done Right Promise in writing. Our technicians are background-checked and uniformed, and a real person answers the phone around the clock. Call (833) 510-5367 for your free estimate.
Written by the team at Bradford Remodeling Co Coral Gables, serving Coral Gables and nearby areas.












