







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Bathroom Remodeling: The Coral Gables Owner’s Guide
Schluter bathroom remodeling in Coral Gables typically runs $9,000 to $28,000 installed, whether you’re rebuilding a failed shower with Schluter’s Kerdi waterproofing system or replacing a cracked shower tray. We install Schluter-compatible assemblies – waterproofing membranes, shower trays, linear drains, and trim profiles – and we put the price in writing before any work starts. A live person answers our phone whenever you call.
Most Coral Gables owners don’t discover a Schluter problem until water shows up where it shouldn’t. The grout line at the shower curb darkens and never dries. A soft spot appears in the drywall of the room on the other side. Or a tile pops loose at the drain flange after a few seasons of humidity. Once that happens, the fix is rarely a patch – it’s a rebuild of the waterproofing layer underneath. That’s the part that does the actual work; the tile is just the surface.
Which Schluter Models This Applies To

Schluter’s bathroom line centers on a few product families, and knowing which one is under your tile tells you what a repair involves. Kerdi is the polyethylene waterproofing membrane bonded to the substrate with thin-set. Kerdi-Board is a foam tile backer board with the membrane already fused to it. Schluter-Shower System trays are pre-sloped foam pans, some with a centered drain and some offset for a linear drain. Kerdi-Line covers the linear drains themselves, and DITRA handles uncoupling and vapor under the floor.
You identify the right part three ways: the printed label on the original Schluter carton, the membrane’s printed edge markings (Kerdi membrane prints a wrap logo and product code), and measurements – tray dimensions and drain position are what actually match a replacement to the existing rough-in, not the label alone. Schluter does not sell to homeowners directly; its products move through licensed trade distribution, which is one reason spec accuracy matters. On an OEM-vs-aftermarket call for Schluter specifically, we default to genuine Schluter components. The system’s warranty is built around matched parts, and a knock-off membrane or a tray with the wrong slope defeats the point of installing the system at all. For finish surfaces we work with documented brands including KraftMaid, Cambria, and Silestone. Bradford Remodeling Co Coral Gables is an independent installer of Schluter-compatible systems, not affiliated with Schluter.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Bathroom Remodeling Is Failing
Water is patient. It finds the smallest gap and works on it for months. Here’s how that shows up.
- Grout that darkens and stays dark. Persistent discoloration at the curb, corners, or drain flange means moisture is sitting behind the tile instead of draining off the waterproofing layer. It’s the first sign the assembly is holding water.
- Loose or hollow-sounding tile near a drain or curb. Tap gently with a plastic handle; a dead thud is a detached tile. That usually means the thin-set bond has failed, often from movement or a wet substrate underneath.
- A soft or swollen spot in the wall or ceiling below. In a second-floor Coral Gables bath, a stain on the room behind the shower wall points to a membrane breach at a seam, a penetration, or the curb-to-floor transition.
- Water pooling on the shower floor after use. If a tray isn’t draining cleanly, the pre-formed slope has been damaged or the pan was set out of level. Standing water sits on the waterproofing and stresses every joint.
- Musty odor that returns after cleaning. Coral Gables humidity plus a weeping shower assembly is a mold engine. A smell that won’t quit after a deep clean usually means moisture is trapped where you can’t reach it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed bathroom remodel pricing in Coral Gables runs $9,000 to $28,000. A focused walk-in shower rebuild with a new Schluter waterproofing system lands at $4,500 to $12,000. A tub-to-shower conversion is $3,500 to $10,000, and a straight shower replacement (same footprint) is $3,000 to $8,500. Vanity replacement, if the layout shifts with the rebuild, is $800 to $3,000.
What drives the range: whether you keep the existing footprint or move plumbing, tray type and drain position (a linear drain needs framing work a centered drain doesn’t), tile choice and the labor to set it, and whether the substrate behind the old shower is sound or gets replaced. Our price sheet is line-item: demolition, substrate, membrane and tray, drain, tile, labor. Every project gets a written price before work starts, and there are no numbers that move at the door. All completed work carries the 365-Day Done Right Promise – if something fails within that year, we come back and correct it at no charge.
DIY or Call Us?
You can safely do the inspection. Run the shower and watch where water goes, check for soft spots in adjacent walls, tap tile for hollow spots, and look behind the access panel at the drain connection. Photography is fine. What we don’t recommend is tearing into the waterproofing layer yourself. Schluter systems depend on exact overlap, thin-set coverage, and slope tolerance; a single improperly lapped seam or a tray set a fraction out of level leaks within a month, and by then the damage has spread. On a shower rebuild, water is the danger, not the tools – which is why the disassembly and reassembly belong with someone trained to get the tolerances right. If you’ve found a symptom above, call (833) 510-5367 and we’ll tell you what we think.
FAQs

How long does a Schluter shower system last? A properly installed Schluter waterproofing assembly regularly lasts 20 years or more – the membrane itself has no realistic service life. The tile and grout are the parts that age first, and in South Florida’s humidity, a year of deferred maintenance can shorten the total. Call (833) 510-5367 if you want an honest read on what’s failing.
Can you repair a failed Kerdi shower instead of replacing it? Sometimes. A single compromised tile or an isolated seam can be repaired if the membrane under it is sound. If the whole pan or a wall field is wet behind the tile, patching won’t solve what’s underneath it, and a rebuild is the honest answer. That’s a call we make after inspection, not over the phone.
How long does a shower replacement take? A same-footprint shower replacement typically runs one to two weeks from demo to final grout, and a full bathroom remodel runs longer. Timeline depends on framing, inspection scheduling, and tile lead time. Coral Gables permitting and inspection can add days, so we build that into the written schedule.
How do you source Schluter parts? Through licensed trade distribution, matched to your existing system by product family and rough-in dimensions. We don’t stock parts on hand; we specify and order what your bathroom actually needs. Call (833) 510-5367 to schedule a free estimate – we’ll put a written price in your hands before any work begins.
Every project we run gets the same treatment: a written price before any tool comes out, a clean site at close, and a signed written guarantee in your hand. If you’re in Coral Gables and have a shower that’s telling you something, call (833) 510-5367 for a free estimate. A live person answers around the clock.
Written by the team at Bradford Remodeling Co Coral Gables, serving Coral Gables and nearby areas.












