







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Coral Gables Homeowners Choose Jerith Construction
Bradford Remodeling Co Coral Gables provides independent Jerith construction service in Coral Gables: fence and railing installation, repair, and replacement for the Estate, Infinity, ProSeries, and Traditions product lines. What sets our Jerith work apart is that we fit the components to coastal South Florida conditions instead of treating a fence as a boxed product that goes in the same way on every lot. Salt air, hurricane-wind requirements, and Coral Gables’ own Board of Architects review all shape how a Jerith run should be built, and we plan for each one before the first post goes in the ground.
We’re an independent Jerith service provider. Bradford Remodeling Co Coral Gables is not affiliated with, sponsored by, or authorized by Jerith, and we don’t speak for the manufacturer. Our technicians have up to 22 years of experience installing and repairing these systems, and we hold every project to The Garrison Standard: a written price before work starts and the 365-Day Done Right Promise behind the finished job. Call (833) 510-5367 for a free estimate.
Why Trust Bradford Remodeling Co Coral Gables for Your Jerith Construction?

Jerith aluminum and vinyl fencing has particular habits, and knowing them shortens a job. The extruded channel dimensions on an Estate panel, the hinge spacing on an Infinity gate, the routed post slots on a Traditions privacy run: these aren’t interchangeable with other manufacturers’ parts, and a crew that treats them that way ends up with a gate that won’t latch or a panel that rattles in wind. Our technicians have handled the Estate, Infinity, ProSeries, and Traditions lines across Coral Gables and South Florida, so they recognize the difference between a part that has failed and a part that was never set correctly to begin with.
Warranty-safe service is part of the discipline. We use genuine Jerith replacement panels, posts, brackets, and gate hardware where the profile is still in production, because the extruded dimensions and hinge spacing have to match the original run. We don’t drill, cut, or modify a panel in ways that would void a manufacturer warranty, and we document the scope in writing so a homeowner has a paper trail if a warranty question comes up later. Every price is written before work starts. The 365-Day Done Right Promise covers the finished job for a full year: if the installation or repair fails inside that window, we return and correct it at no charge.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Jerith Construction Problems We Fix in Coral Gables
The failures we see on Jerith products in Coral Gables trace back to three forces: salt air, soil movement after summer saturation, and UV. Here are the patterns that actually show up.
- Powder-coat chalking and pitting on aluminum panels. On Estate and ProSeries runs near Biscayne Bay and the Atlantic, salt-air exposure breaks down the powder coat faster than the manufacturer’s finish warranty assumes, and the lower rails go first where irrigation spray and lawn chemical drift collect. The symptom is a chalky, rough surface that holds dirt and eventually pits. Re-coating can buy years on an otherwise sound panel; deep pitting means that section is done.
- Post-base failure and gate sag. Aluminum posts set in shallow concrete footings or straight into soil lean and rack after a few wet seasons, and a gate hung on a leaning post will drag and miss the latch even when the panels look square. The fix is resetting or replacing the affected posts with properly sized footings, not adjusting the hinge over and over.
- Vinyl Traditions cracking and bowing. Routed post slots and bottom rails on a Traditions privacy panel take the worst of South Florida UV and heat buildup. Panels crack at the routed slot or bow along the bottom rail, and an unsupported privacy run can catch wind lift in a storm. Steel or aluminum reinforcement inside the post, and proper spacing, keep a vinyl run standing.
- Hinge and latch corrosion. Aluminum hinges and self-closing latches seize or lose tension in salt air, and a gate frame twists out of square when it’s hung on non-rackable panels that can’t follow grade. Replacing the hardware is usually the answer when the frame itself is true.
- Racked panels on sloped lots. Coral Gables lots roll, and a rackable Estate panel is designed to step with the grade. A crew that forces a non-rackable panel to follow a slope ends up with pickets out of plumb and a run that looks wrong from the street. The right panel for the grade is the whole point.
A typical Jerith job starts with a homeowner noticing a gate that drags or won’t latch, and pickets that have gone chalky and rough on the south-facing side. The usual cause is a shallow or undersized concrete footing that has shifted with seasonal soil saturation, combined with sun and salt-air breakdown of the powder coat on the lower rails. A qualified local pro resets or replaces the affected posts with properly sized footings, re-squares and re-hangs the gate with new hardware, and either re-coats or replaces damaged panels to match the existing run.
Jerith Parts & Our Repair-vs-Replace Approach

Parts sourcing drives the quality of a Jerith repair, and it’s where corners get cut. We use genuine Jerith replacement panels, posts, brackets, and gate hardware where the profile is still in production, because the extruded channel dimensions and hinge spacing have to match the original run. We match color and finish batch on visible sections so a repair doesn’t read as a patch from the street. We don’t claim to stock Jerith parts locally; components are sourced per job so the right profile, finish, and batch get ordered for your specific fence.
Repair versus replace is an honest call, not a sales one. When a run is discontinued or the damage is isolated to one section, repairing the affected span is usually smarter and cheaper than tearing out a full perimeter that’s still sound. A fence that has failed at multiple footings after repeated storm seasons is normally a replace-not-patch decision, because patching one post only moves the problem down the line. We’ll tell you which situation you’re in, in writing, before any work is scheduled. Call (833) 510-5367 for a free estimate.
Our Jerith Service Process – Step by Step
- 1
Diagnosis. We look at the whole run, not just the visible fault: post footings and grade, panel and rail condition, powder-coat or vinyl wear, and gate hardware. On an Estate or Infinity gate the hinge spacing and frame square get measured, because a sagging gate is usually a footing problem disguised as a hardware problem.
- 2
Written scope and price. Before work starts, you get a written price with the scope spelled out: which posts get reset, which panels get replaced, which hardware gets swapped. No number that moves at the door.
- 3
Repair or install. Posts go in with properly sized concrete footings set for Coral Gables’ high water table and limestone bedrock. Panels are racked to grade, gates are re-squared and hung with new Jerith hardware, and finish is matched to the existing run.
- 4
Test and walk-through. Every gate gets opened, closed, and latched repeatedly. Panels get checked for plumb and wind movement. We walk the finished job with you and hand over the signed written guarantee.
- 5
365-Day Done Right Promise. Every completed project carries a full-year written guarantee. If the work fails inside that window, we come back and correct it at no charge.
See the difference
Before
After
Before
After
Before
AfterJerith Products We Service & Install in Coral Gables
We service and install the Jerith aluminum and vinyl lines sold in South Florida, and we don’t claim stock of any of them: parts are ordered per job to match your run. Aluminum lines include the Jerith Estate ornamental fencing, with rackable panels and welded pickets; the Jerith Infinity series, with its low-profile decorative top rail; and the Jerith ProSeries, in 2-rail and 3-rail residential profiles. On the vinyl side, we handle the Jerith Traditions line, including privacy and picket panels with routed posts. For installations that pair a fence with a driveway or an addition, we also cover paver driveways and home additions, so the property gets finished as one coordinated job instead of three contractors tripping over each other.
We Also Service These Brands
Bradford Remodeling Co Coral Gables is multi-brand, not single-brand dependent. Alongside Jerith, we install and service KraftMaid cabinetry, Cambria and Silestone surfaces, and Kohler fixtures, backed by a documented roster of manufacturer specs and warranties. If a project touches the fence and the kitchen at the same time, that range matters.
FAQs – Jerith Construction Service in Coral Gables

No. Bradford Remodeling Co Coral Gables is an independent Jerith service provider, not affiliated with, sponsored by, or authorized by Jerith. We work on Jerith products as an independent contractor and don’t speak for the manufacturer. Our technicians have up to 22 years of experience with these systems, and every job carries a written price and the 365-Day Done Right Promise.
Yes, where the profile is still in production. We use genuine Jerith replacement panels, posts, brackets, and gate hardware because the extruded channel dimensions and hinge spacing must match the original run. On discontinued profiles, we source a matching-quality aftermarket component and tell you plainly that it’s aftermarket before ordering. Call (833) 510-5367 to confirm what’s available for your series.
A single-section repair or a gate re-hang is usually a few hours; a full run replacement or a new install takes longer and depends on part lead times and Coral Gables permit review. Parts are ordered per job, so the schedule starts once the profile is confirmed. Call (833) 510-5367 for a written scope and timeline.
We cover the Jerith aluminum and vinyl lines sold in South Florida: the Estate ornamental fencing, the Infinity series, the ProSeries 2-rail and 3-rail residential profiles, and the Traditions vinyl privacy and picket panels. If you’re unsure which series you have, a photo of the post, rail, and gate hardware usually tells us. Call (833) 510-5367 and we’ll identify it before quoting.
Not when the work is done correctly. We use genuine Jerith parts where the profile is in production, don’t modify panels in ways that would void the manufacturer’s coverage, and document the scope in writing so you have a paper trail. As an independent provider, we can’t act on the manufacturer’s behalf, but the work itself is covered by our 365-Day Done Right Promise for a full year. Call (833) 510-5367 with your warranty questions.
Here are the ranges we quote in Coral Gables, written before work starts:
| Service | Typical Coral Gables Range |
|---|---|
| Aluminum Fence Installation (includes Jerith Estate, Infinity, ProSeries) | $4,000 – $10,000 |
| Vinyl Fence Installation (includes Jerith Traditions) | $3,500 – $9,000 |
| Paver Driveway Installation | $7,000 – $18,000 |
| Home Addition | $45,000 – $130,000 |
Single-section repairs and gate re-hangs are quoted individually, since they depend on the profile, footing condition, and hardware. Your price is written down before work starts and doesn’t move at the door. Call (833) 510-5367 for an exact quote; estimates are free.
Book Your Jerith Service in Coral Gables, FL
Whether it’s a sagging Estate gate, a chalky Infinity run, or a new Traditions privacy fence, Bradford Remodeling Co Coral Gables gives you a written price before work starts, genuine Jerith parts where the profile is available, and the 365-Day Done Right Promise on the finished job. Every Coral Gables project ends squared away: clean site, documented scope, and a signed written guarantee in your hand. Call (833) 510-5367 for a free estimate.
Written by the team at Bradford Remodeling Co Coral Gables.












