







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
James Hardie Kitchen Remodeling: The Coral Gables Owner’s Guide
James Hardie kitchen remodeling in Coral Gables typically runs $14,000 to $45,000 installed, depending on kitchen size, cabinet layout and surface selections. We install James Hardie’s fiber cement exterior products and lap siding as part of whole-kitchen scopes that touch exterior walls, additions and window openings, and we handle the associated plumbing, electrical rough-in and finish work in one written scope. That written price comes before any work starts.
When the James Hardie side of a kitchen job fails, owners usually find it the same way: a hairline crack at a seam above a window, paint flaking off the lap siding outside the kitchen, or water staining on the wall board around a pass-through. By the time it’s visible indoors, the exterior layer has usually been weeping for a season or two. That’s the pattern we see most in Coral Gables homes built or renovated between 2005 and 2015.
Key Takeaways
- Kitchen remodeling with James Hardie exterior integration in Coral Gables: $14,000 to $45,000 installed.
- Smaller kitchen scopes: $9,000 to $20,000. Cabinet installation alone: $4,000 to $13,000.
- Fiber cement siding is a hard product to repair in place without matching the profile and texture. Mis-matched patching is the single biggest reason a siding failure returns.
- Every completed James Hardie scope carries the 365-Day Done Right Promise: if the work fails inside that window, we return and correct it at no charge.
Which James Hardie Models This Applies To

James Hardie’s fiber cement siding lines split into three families that show up on Coral Gables home exteriors: HardiePlank lap siding, HardiePanel vertical siding and HardieShingle. Kitchen remodels that touch an exterior wall almost always intersect one of these. The product line, thickness and profile are stamped on the back of every plank – you’ll see the HardiePlank logo, a product code and a lot number. If a contractor can’t point to that stamp on the back of a piece, you’re not looking at genuine James Hardie material.
Lap siding is sold in nominal 5-1/4 inch exposures with an actual thickness of 5/16 inch, which matters when you’re matching existing courses during a kitchen bump-out. HardiePanel is 4×8 or 4×10 sheets at the same 5/16 inch thickness. HardieShingle comes in staggered and straight-edge profiles and is the most common mismatch headache – it’s easy to order the wrong stagger. When we order, we pull the product code from a piece we’ve removed, not from memory or a photo.
Between OEM and aftermarket, we source genuine James Hardie product for any visible exterior surface. The color and texture system (ColorPlus and the factory finishes) is baked into the product, not applied later, and a lookalike won’t match the existing wall. On hidden substrate behind the siding – the sheathing and weather barrier – we spec name-brand material where it doesn’t change the finished look. For the kitchen itself, we work from KraftMaid and Wellborn cabinetry and Cambria, Silestone or Caesarstone surfaces. Bradford Remodeling Co Coral Gables is an independent remodeling contractor and is not affiliated with James Hardie.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your James Hardie Kitchen Remodeling Is Failing
- Cracks at seam lines above windows and doors. Fiber cement is rigid; when a wall opening moves and the siding doesn’t, the seam catches the movement. A single hairline crack is normal settling. A crack that returns after caulking is the substrate moving.
- Paint or finish flaking on the exterior wall of the kitchen. James Hardie’s factory finish is designed to hold, but sun exposure on a south or west wall in South Florida will break down the surface coat over time. Flaking that starts in one spot and spreads is the finish failing, not the board.
- Moisture staining or soft drywall inside the kitchen. Usually water has entered at a window head, a pass-through opening or the transition where the kitchen addition meets the original wall. This is the most expensive failure to catch late because it reaches framing.
- Visible gaps at the trim/siding joint. When caulk ages out or the wrong sealant was used at install, the joint opens. Gaps at the corner trim and above window heads are the most common entry point.
- Board swelling or delamination at the bottom course. Fiber cement resists water well, but it isn’t immune. If the bottom course has absorbed water repeatedly – from splashing, irrigation or a path that drains toward the house – the edge will fail before the face does.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

A kitchen remodeling project with integrated James Hardie exterior work in Coral Gables runs $14,000 to $45,000 installed. That top number is driven by square footage, whether a wall has to be opened, cabinet and surface selections, and how much of the exterior siding needs to be matched or replaced to close the scope. The bottom of the range covers a compact kitchen with stock cabinetry, laminate or entry-level surfaces and a small siding repair at the pass-through or window opening.
Line-item pricing for the most-asked pieces:
| Scope | Installed Range (Coral Gables) |
|---|---|
| Full kitchen remodel with James Hardie exterior integration | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
Parts and labor are broken out on the written quote – you see what the siding and trim cost, and what the installation costs. No line moves after the price is signed. Every completed project carries the 365-Day Done Right Promise, a full-year written guarantee covering any failure inside that window at no charge.
DIY or Call Us?
An owner can safely do three things: read the HardiePlank stamp on the back of a removed piece to identify the product, measure the exposure of the existing courses (usually 5-1/4 inches) to confirm what needs to match, and photograph any crack or gap so it’s documented before anyone works. That’s it.
What goes wrong on DIY: cutting fiber cement without the correct blade and respiratory protection, replacing siding without re-flashing the opening (which lets water in behind the new board), matching the factory finish with a brush-on paint, and re-caulking a joint that was moving when it cracked. Any of these turns a siding repair into a water-intrusion project. And if the work approaches a window head, a pass-through opening or anything near an electrical rough-in, we recommend a trained professional, and we recommend it without hedging. Call (833) 510-5367 and we’ll walk you through what the failure looks like in person.
FAQs

Factory-finished James Hardie siding commonly holds 20 to 30 years on a properly flashed wall, but the South Florida sun is the number that moves. West and south-facing walls in Coral Gables carry the worst load, and finish failure usually shows up before product failure. The substrate behind the siding is where the real lifespan gets decided.
Often, yes. A single cracked board above a window, a failed sealant joint or a damaged corner piece can be replaced individually when the surrounding substrate is sound. The full-field replacement call belongs to a water-damaged wall, not a surface crack. We’ll tell you which one you have before you commit to anything.
A single siding repair or one-course replacement is typically a partial-to-full day, weather permitting. A full exterior integration on a kitchen bump-out adds days to the overall timeline, driven by matching courses, re-flashing openings and re-finishing. We put the timeline in the written scope so it doesn’t drift.
We pull the product code from a piece already removed from your wall – HardiePlank, HardiePanel or HardieShingle, the thickness and the lot – and order to that code. When a match isn’t possible, we tell you that up front and price the correction honestly rather than hiding a mismatch behind caulk. Call (833) 510-5367 to schedule your free estimate.
Written by the team at Bradford Remodeling Co Coral Gables, serving Coral Gables and nearby areas.












