







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Coral Gables Homeowners Choose CGI Construction
We provide independent CGI construction service in Coral Gables: cabinet installation and refacing, quartz countertop work, and standing seam metal roofing, all done to the product’s own specs. What makes our CGI work different is that we treat the brand as a set of real assemblies (Premier Series boxes, StoneCraft slabs, SummitStanding Seam panels) with known failure points in South Florida humidity, salt air, and hurricane-zone wind loads, not as a logo. We are not authorized, sponsored, or endorsed by CGI. We’re an independent CGI service provider that works on these products daily. Every job starts with a written price, and every finished project carries our 365-Day Done Right Promise. Call (833) 510-5367 to schedule a free estimate.
Why Trust Bradford Remodeling Co Coral Gables for Your CGI Construction?

Our technicians have up to 22 years of experience, and a good share of that has been spent on CGI product lines specifically. They know that a Premier Series hinge repair succeeds or fails based on whether the installer deals with the swollen particleboard behind the screw, not just the screw itself. They know that StoneCraft quartz chips at sink cutouts for two reasons: over-torqued undermount clamps and an under-supported deck. Correcting the cause is the difference between a repair that lasts and a callback.
Parts matter. We source CGI OEM hinges, drawer glides, and panel clips when they preserve factory fit and finish, and we’ll tell you plainly when a component is discontinued and a quality aftermarket equivalent from an established hardware maker is the smarter buy. Nothing is guessed at. The scope, the parts, and the price are in writing before any tool comes out, which is The Garrison Standard at work. We operate as an independently owned and operated member of the Garrison Partners family, held to that standard, and we’re clear about what the guarantee covers: if the work fails inside the 365-day window, we come back and correct it at no charge.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common CGI Construction Problems We Fix in Coral Gables
Coral Gables sits on limestone with a high water table and takes hurricane-season wind-driven rain off Biscayne Bay. That combination finds weak points in cabinetry and roofing fast. Here are the CGI issues we see most, and why they happen.
- Premier Series doors sagging or rubbing at the stile. Hinge screws lose their bite in particleboard side panels that have swelled through a few wet seasons. The door drops a fraction and starts kissing the adjacent stile. Left alone, the hinge pulls further and the box face degrades.
- StoneCraft quartz chipping at the sink edge. Undermount clamps torqued too tight, or a deck with too little support under the cutout, concentrates stress right at the rim. A chip there isn’t cosmetic; it’s where water gets in.
- Reflections Series vanity finish blistering near the toe kick. Slab moisture wicks up through unsealed MDF at the floor line. Sealing the toe kick and managing the moisture source is the fix; refinishing over a wet substrate just delays the problem.
- SummitStanding Seam panel oil-canning. Thermal cycling on low-slope Florida roofs makes flat panel fields flex and dimple. It’s cosmetic until fasteners start backing out at the pan seam, then it’s a water-entry path.
- Fastener back-out at pan seams. Wind uplift plus repeated expansion and contraction works fasteners loose over time. Re-securing with seam clamps and new fasteners is usually the right call, not tearing off panels.
CGI Parts & Our Repair-vs-Replace Approach

We don’t keep a local parts warehouse, and we won’t pretend otherwise. What we do is source the right component for each job: CGI OEM hinges, glides, and clips where they preserve fit and finish, and proven aftermarket hardware from established makers when an OEM part is discontinued or slow to ship. Both paths are legitimate. We tell you which one applies and why before we order anything.
Repair is usually the honest answer for door and hardware problems and for countertop edge damage, because the boxes and the slab are still sound. Full replacement makes sense when cabinet boxes have swollen past the point of a clean hinge repair, or when a roof panel field has lost seam integrity across enough of the run that patching becomes a losing game. We’ll show you what we’re seeing and give you a written price on both paths so the decision is yours. Call (833) 510-5367 and we’ll walk a repair-vs-replace question through with you.
Our CGI Service Process – Step by Step
- 1
Diagnosis. We inspect the actual failure, not just the symptom, whether that’s a rubbing Premier Series door, a StoneCraft chip, a blistered Reflections toe kick, or a SummitStanding Seam seam with backed-out fasteners. We check adjacent boxes and panels for the soft spots that caused the problem.
- 2
Written scope and price. You get the parts list, the method, and a firm price in writing before work starts. No numbers that move at the door.
- 3
Repair or install. Hinge repairs get hardwood inserts or repair plates and fresh CGI-spec hinges. Countertop edge repairs get the deck properly supported and the clamps set to spec. Roof seams get re-secured with seam clamps and new fasteners.
- 4
Test. Doors get cycled and checked for rub. Countertops get checked for level and secure mounting. Roof seams get a water test and a fastener torque check.
- 5
Warranty handoff. You get a signed 365-Day Done Right Promise in hand at close, on a clean site, with the documented scope on file.
See the difference
Before
After
Before
After
Before
AfterCGI Products We Service & Install in Coral Gables
We work across the CGI lines Coral Gables homeowners actually own: Premier Series plywood-box cabinetry for kitchens and built-ins, StoneCraft quartz countertops, Reflections Series bathroom vanities, and SummitStanding Seam metal roofing. Cabinet installation and refacing, quartz and granite countertop work, and standing seam metal roofing are the three sub-services we handle most on this brand. We don’t claim to stock these products locally; we spec and source them per job. Because Coral Gables runs most exterior work through its Board of Architects, a standing seam roof or exterior cabinet change here often needs design review before a single panel or box goes in, and we plan that timeline into the written scope rather than letting it surprise you mid-job.
We Also Service These Brands
Bradford Remodeling Co Coral Gables is a multi-brand contractor, not a single-brand shop. Alongside CGI, we work with KraftMaid and Wellborn cabinetry, Cambria, Silestone, and Caesarstone surfaces, and Kohler and Moen fixtures, among others in our approved brand set. That matters when a CGI repair turns into a mixed-material decision: a StoneCraft slab next to a KraftMaid run, or a Kohler sink under a CGI quartz deck. We can handle the whole scope on one written price instead of sending you to a second contractor.
FAQs – CGI Construction Service in Coral Gables

The CGI Premier Series uses plywood boxes, which handle Coral Gables humidity better than legacy particleboard construction, though the door and hinge hardware still need moisture-aware repair when screws pull out of swollen panels. Plywood resists swelling at the fastener points far better than particleboard, but no cabinet is immune to a bathroom or kitchen that stays damp. Sealing the toe kicks and managing interior moisture is the real long-term answer. Call (833) 510-5367 for an estimate on a Premier Series install or repair.
Yes, a StoneCraft quartz chip at the sink edge can usually be repaired, and repair is often the right call if the slab is otherwise sound and the chip is localized. The technician’s job is to correct the cause first, supporting the deck and resetting undermount clamps to spec, then color-matching and finishing the chip. If the chip is at a clamp point that was over-torqued, fixing the clamp before the finish is what keeps the repair from failing again. Call (833) 510-5367 for an exact quote; estimates are free.
A CGI SummitStanding Seam roof can work on low-slope applications when panels, seam spacing, and fastening are spec’d for the pitch and Miami-Dade’s High-Velocity Hurricane Zone product approvals. The failure to watch is oil-canning and fastener back-out at the pan seams after thermal cycling. A correct install plans for that movement. So does a correct repair, which typically re-secures the seam with new fasteners rather than replacing panels. Call (833) 510-5367 to schedule a free roof assessment.
Blistering near the toe kick on a Reflections Series vanity is almost always slab moisture wicking up through unsealed MDF at the floor line, not a defect in the finish itself. Sealing the toe kick and addressing the moisture source is the fix; re-facing over a wet substrate won’t hold. Call (833) 510-5367 for a quote on sealing or replacing the affected components.
OEM CGI hinges and glides are the best choice when available because they preserve factory fit and finish, but a quality aftermarket equivalent from an established hardware maker is a sensible substitute for discontinued or slow-ship components. Either way, the repair should address the swollen panel behind the screw, not just swap the hinge. We’ll tell you which path applies before we order. Call (833) 510-5367 for an exact quote; estimates are free.
CGI construction costs in Coral Gables depend on the specific product and scope; the ranges below are written-price territory, not phone-quote territory. Cabinet installation, countertop work, and standing seam roofing each carry their own range, and Coral Gables’s Board of Architects review can add 60 to 90 days to exterior jobs, which we plan into the scope. Call (833) 510-5367 for an exact written quote; estimates are free.
| CGI Service | Typical Range in Coral Gables |
|---|---|
| Cabinet Installation | $4,000 – $13,000 |
| Countertop Installation | $2,000 – $6,500 |
| Kitchen Island Installation | $3,000 – $10,000 |
| Walk-In Shower Installation | $4,500 – $12,000 |
| Tub-to-Shower Conversion | $3,500 – $10,000 |
| Standing Seam Metal Roof | $15,000 – $40,000 |
| Roof Repair | $400 – $1,800 |
Book Your CGI Service in Coral Gables, FL
CGI Premier Series cabinets, StoneCraft countertops, Reflections vanities, and SummitStanding Seam roofs each have a failure mode we know how to correct. You get a written price before work starts and a signed 365-Day Done Right Promise at close. A live person answers the phone 24/7. Call (833) 510-5367 for a free estimate.
Written by the team at Bradford Remodeling Co Coral Gables.












