







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Fence Installation: The Coral Gables Owner’s Guide
Barrette fence installation in Coral Gables typically runs $3,500 – $9,000 for a standard residential run, and we handle the assessment, the correct Barrette-series component match, and the install as one documented scope. We’re an independent service provider, not affiliated with Barrette, but we work with their aluminum and vinyl systems often enough to know where they fail in South Florida. Most owners discover a problem the same way: a post starts leaning after a summer storm, a gate sags and drags, or a section of picket pulls loose at the rail. Then they look closer and find rust bloom at the fasteners or a hairline crack at the post base.
Key takeaways:
- Installed Barrette-compatible fence work in Coral Gables: $3,500 – $9,000.
- The part that fails first is almost never the panel. It’s the post setting and the fasteners.
- You get a written price before any work starts, under The Garrison Standard.
- Every completed install carries the 365-Day Done Right Promise in writing.
Which Barrette Models This Applies To

Barrette’s residential fence lines split into aluminum (ornamental, rackable, and pool-code profiles) and vinyl (privacy, picket, and semi-privacy). Within each, the part you need is tied to two things: the rail height and the post cap style. A 54-inch aluminum panel does not share rails with a 48-inch run, and mixing them is the single most common compatibility mistake we correct. Before we quote, we identify your system three ways: the stamped mark on the inside face of the rail or post, the actual measured panel width (Barrette runs commonly land near 6 feet nominal, but measure – nominal is not the same as true), and the post cap profile.
On the OEM-versus-aftermarket question, it depends on the part. Brackets, caps, and gate hardware are worth matching to the exact Barrette series because a cap that’s 1/8 inch off will not seat and will collect water. Rails and pickets can often be matched from a quality equivalent profile when the OEM piece is discontinued, provided the wall thickness and finish spec line up. Barrette’s powder-coat aluminum and their vinyl formulations behave differently in salt air and summer UV, so a finish substitution is not a neutral swap – we check it against the manufacturer spec before recommending it. We don’t stock parts and we don’t carry an inventory on a truck; we source to your model.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Barrette Fence Installation Is Failing
- Posts leaning after rain. In Coral Gables, the limestone and sandy fill under a lot drains fast, and a post set in a shallow concrete footing will rock within a season. The lean is the footing talking, not the post.
- Rust at the fasteners and rail ends. Salt air off the Bay eats through cheap self-tapping screws long before the aluminum gives out. You’ll see orange staining at the bracket holes first.
- Gate sag and drag. Gate hardware is the highest-load part on the whole run. When the hinge screws wallow out the post wall, the gate drops – a hardware problem, not a frame problem.
- Pickett or panel pulling from the rail. Usually a failed rail insert or a screw that backed out of thin wall aluminum. Left alone, wind load opens the gap fast during storm season.
- White chalking or hairline cracks on vinyl. South Florida UV is brutal on vinyl. Chalking is cosmetic; cracking at a rail or post junction means the part is at end of life.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For Coral Gables, expect $3,500 – $9,000 installed for Barrette-compatible fence work. The range moves on run length, whether footings need to be reset (the biggest single driver), gate count, and finish selection. Parts and labor are broken out line by line in the written price – you see what the component costs and what the install costs before anything is ordered. There are no numbers that move at the door.
| Scope item | Typical installed range |
|---|---|
| Section repair with matched Barrette components | $350 – $1,200 |
| Gate hardware replacement and re-hang | $250 – $800 |
| Post reset with new footing | $400 – $1,100 per post |
| Full residential run, installation | $3,500 – $9,000 |
All completed work is covered by the 365-Day Done Right Promise: if the install fails within a year – a post shifts, hardware loosens, a section pulls – we come back and correct it at no charge. That’s a written guarantee, not a handshake.
DIY or Call Us?
You can safely check a few things yourself: measure a panel width, look for the stamp inside the rail, note where rust or cracking shows, and photograph the footing base. Where DIY goes wrong is the post setting and the gate geometry. A post that looks plumb in dry weather will lean once the summer water table moves, and a gate re-hung without checking post plumb will sag again in weeks. If a post is visibly rocking or a section has pulled free, that’s a structural footing issue, not a screw-tightening job – stop and let a crew assess it. Fasteners into a compromised post wall can let a whole panel drop under wind load. Call (833) 510-5367 and we’ll give you a written scope before anything is touched.
FAQs

A properly installed aluminum Barrette system will outlast vinyl in South Florida’s salt air, typically 15 – 20 years for the metal components with the finish holding well; vinyl runs shorter, often 10 – 15 years, because UV exposure degrades the material faster here than in cooler climates. The footing and fasteners are what usually decide the real lifespan, not the panel.
Usually yes. A single failed section, a sagging gate, or one bad post is a targeted repair, not a full replacement, and it’s the cheaper route most of the time. We’ll tell you plainly if the damage has spread far enough that repair stops making sense. Call (833) 510-5367 for a free assessment and a written price either way.
A single section or gate repair is typically a one-day job; a full residential run in Coral Gables runs longer and depends on how many footings need resetting. You get the timeline in the written scope before we start, so there are no surprises.
We identify your model from the stamped mark and measurements, then source the matching component against the manufacturer spec. We don’t keep a parts inventory on hand and won’t claim to – the match is made to your system, verified before install.
We work with a documented roster of name-brand materials across our projects, including KraftMaid, Cambria, and Silestone on the interior side, and we hold every fence install to the same written-price, written-guarantee standard – The Garrison Standard – that governs every job we run. Background-checked, uniformed technicians, and a live person answers the phone around the clock.
Call Bradford Remodeling Co Coral Gables at (833) 510-5367 to schedule your free estimate. You’ll get the full price range in writing before any work begins.
Written by the team at Bradford Remodeling Co Coral Gables, serving Coral Gables and nearby areas.












