







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Bufftech Home Additions & ADU: The Coral Gables Owner’s Guide
We install and service Bufftech-compatible home additions and ADU components across Coral Gables, and a full addition or ADU build here typically runs $45,000 – $130,000 depending on size, lot constraints, and finishes. When an owner calls us about this kind of part, it’s rarely one clean failure. It’s usually a symptom they noticed weeks ago and finally got tired of: a door that won’t latch square because the frame has shifted, a Florida-room transition that leaks during a summer squall, or a header that started sagging after a few wet seasons. Bufftech pieces sit inside a house’s envelope, so when one goes, the signs show up at seams and openings before they show up anywhere obvious.
Which Bufftech Models This Applies To

Bufftech builds a wide range of exterior and structural component lines, and the right replacement part has to match the series and the profile, not just the general look. Before we quote anything in Coral Gables, we identify the part three ways: the stamped label on the original unit (usually tucked inside the jamb or on the hinge stile), a caliper measurement of the extrusion or hinge profile, and the rough opening dimension. Those three together tell us the series line.
From there it’s the OEM-versus-aftermarket decision. OEM Bufftech pieces match the original spec exactly, which matters when the part sits inside a load path or a wind-rated assembly. Quality aftermarket equivalents can be a good call for non-structural trim and finish pieces, and they often cost less and arrive faster. We don’t stock parts, and nothing rides on a truck waiting for you. We spec the part against your measurements, order it, and install what arrives. Bradford Remodeling Co Coral Gables is an independent service provider and is not affiliated with Bufftech.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Bufftech Home Additions & ADU Is Failing
- Sticking or misaligned openings. A door or window in the addition that suddenly drags or won’t latch usually means the frame or header has shifted, often from moisture movement in the substrate.
- Water staining at seams and transitions. Coral Gables gets heavy summer rain and salt-laden air, and Bufftech assemblies that lose their seal at a transition will let water track into the wall cavity. Staining or soft drywall near a joint is the tell.
- Sagging roofline or ceiling. A dip in a flat or low-slope roof over an addition points to a failing structural member or a header that’s carrying more than it should.
- Cracks along the addition-to-house junction. Hairline cracks are normal settling; widening cracks that reappear after patching mean the two structures are moving independently.
- Drafty or damp interior walls. Cool spots, condensation, or a musty smell inside the addition usually trace to a failed flashing or seal at an exterior Bufftech component.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

A Bufftech home addition or ADU project in Coral Gables runs $45,000 – $130,000 installed, and the range moves with square footage, whether the lot needs new foundation work, wind-rated assembly requirements, and finish level. A garage conversion to an ADU is a different scope and lands at $30,000 – $80,000; ground-up ADU construction runs $90,000 – $220,000.
What drives the number most is structural repair behind the failing part. A trim swap is one thing; correcting a shifted header or a compromised seal is another. Every Bradford quote is a written line-item price before any work starts, with parts, labor, and permits broken out, and the number doesn’t move at the door. All completed work carries our 365-Day Done Right Promise: a full-year written guarantee, and if the work fails inside that window, we come back and correct it at no charge.
DIY or Call Us?
An owner can safely check the basics: look for the stamped label, measure the opening, photograph the seam or crack, and note whether the issue gets worse after rain. That information helps us spec the right Bufftech part fast.
What you shouldn’t do yourself is remove or replace a structural member, open an exterior wall to chase a leak, or reset a header inside a load path. Those are where DIY goes wrong, and in Coral Gables’ wind-rated construction, an improperly resealed assembly can fail inspection or worse. Our technicians have up to 22 years of experience with these assemblies. Call (833) 510-5367 to schedule a free estimate and we’ll tell you straight what’s failed and what it takes to fix it right.
FAQs

Most Bufftech exterior components should hold 15 to 25 years in South Florida conditions, but Coral Gables’ salt air, humidity, and heavy summer rain shorten that if seals and flashings aren’t maintained. A part that’s failing well before that usually points to an installation or water-intrusion issue, not the part itself. Call (833) 510-5367 for an exact assessment and quote, free of charge.
Sometimes, yes. Cosmetic or trim components can often be repaired or resealed, while structural members and anything inside a wind-rated assembly usually need full replacement. We’ll tell you which one you’re looking at before any work is priced. Call (833) 510-5367 for a free estimate.
A straightforward component replacement takes one to two days, while structural correction behind a failed part can run a week or more depending on permits and inspection. We give you the timeline in writing with the price. Call (833) 510-5367 to schedule your free estimate.
We identify the series from the label and measurements, then order either the OEM Bufftech piece or a quality aftermarket equivalent based on what the assembly requires. We don’t keep parts in stock or on a truck; we spec and order to your job. We also work with KraftMaid, Cambria, and Silestone finishes when an addition includes cabinetry or surfaces. Call (833) 510-5367 for a free estimate.
If a Bufftech component in your Coral Gables addition or ADU has started to fail, don’t wait for it to get worse. Call Bradford Remodeling Co Coral Gables at (833) 510-5367 for a free estimate, with a written price before any work starts and a full-year guarantee on the work when it’s done.
Written by the team at Bradford Remodeling Co Coral Gables, serving Coral Gables and nearby areas.












